Logo
sales@nowolves.com

Vinyl Decals and Bumper Stickers

 

Showing your opinion on the growing wolf problem has never been easier.

Our decals are precision cut from a premium grade automotive vinyl. We also use a clear high tack transfer tape to make decal placement and transfer easier than ever. Decals will stick to any clean smooth surface without the use of water and transfer fluid.
See application instructions below.

Quantity discounts are also available in cart.

SOS Window Vinyl

 

                    

 

 8.5" X 9.25" 6" X 6"
SOS Vinyl decal 6x6
Quanity
Quanity
 8.5" X 9.25"  7" X 9.25"
SSS Vinyl Decal  Smoke a pack a day vinyl decal
Quanity
Quanity
   
9.5" x 8.5" 9.5" x 8.5"
BOY Piss on Wolves ELK Piss on Wolves
Quanity
 
Quanity
 
IDAHO Available for any state
 6" X 19" Approximate Size  6" X 19"
Kill the wolves in Idaho Kill the wolves in Idaho
Quanity
Quanity
Type State to replace Idaho
   
Bumper Sticker 10" X 3" Bumper Sticker 10" X 3"
Save 1000 Elk Smoke a Pack Responsible Sportsman Shoot and Release
Save 100 Elk Bumper Sticker Responsible Sportsman Shoot and Release
Quanity
Quanity
Bumper Sticker 10" X 3" Bumper Sticker 10" X 3"
Canadian Wolves Smoke a Pack a Day SOS Shoot On Sight
Canadian Wolves Smoke a Pack a Day SOS Shoot On Sight
Quanity
 
Quanity
 
Bumper Sticker 10" X 3" Bumper Sticker 10" X 3"
Shoot Shovel and Shut Up Sample Pack 1 of each bumper sticker (5 stickers)
Shoot Shovel and Shut Up Sample Pack
Out of stock
 
Out of stock
 
   
   

Vinyl application Instructions

Materials Needed
1. Plastic Squeegee (Plastic credit card will work fine also) - Used to smooth out and flatten the vinyl decal.
2. Sewing Pin. Chances are you’ll get bubbles in your installation job, this happens with 90% of vinyl installations.
    Use this to prick any bubbles to release trapped air under the graphic.
3. Roll of Masking Tape - Used to hold the decal to the surfaces during installation, and to insure the decal is level.

Surface Preparation
All surfaces must be thoroughly cleaned before applying your vinyl graphics. The cleaner your surface is the better the vinyl decal will adhere. We recommend first cleaning these surfaces with a soap and water solution. Household dishwashing soap works fine. Next you’ll need Denatured Alcohol to remove any residues. Although you can install decals after cleaning the surface with dishwashing soap we recommend using Denatured Alcohol because it will completely clean the surface.

Temperature and Weather Conditions
The optimum temperature range for vinyl graphic adhesion is 60 - 80 degrees F. The air and surfaces should always be above 40 degrees F. Very high humidity (above 90 percent) may affect the application process.

Application:

Lay the graphic face down on a flat work area. Using a squeegee, credit card, or any flat item, firmly rub graphic area starting from the center and moving out toward the edges. This is to insure that the decal is attached to the “PREMASK”.

Apply a single horizontal strip of 2" masking tape to the top of the graphic. The strip should be split between the graphic and the surface with 1" on each side (as shown). This strip will be used as a hinge that will insure the graphic does not move during the application process.
Hold the bottom edge of the hinged graphic away from the surface and remove the “LINER” to reveal the sticky backing of the vinyl.

CAUTION: Do not let the exposed graphic fall onto the surface. The back of the graphic is very tacky and will tightly adhere to the surface. If the placement is not correct, removing the graphic for re-placement will be very difficult or impossible without causing damage to the vinyl.
While still holding the hinged graphic away from the surface. Use the squeegee and go from top to bottom, begin to merge the graphic to the surface.

Notes: Work from top to bottom. Do not let the entire graphic fall onto the surface. If lines or creases develop, lift and re-place the graphic.
Once the graphic is in proper position and lying perfectly flat on the surface. Go from the center working outward, use firm strokes with the squeegee to insure the elements adhere to the surface.
Gently remove the “PRE-MASK”. Be careful not to pull the graphic up with the “PRE-MASK” paper.

 

nowolf logo

No Canadian wolves